green laser pointer have infrared and radio frequency

  green laser pointer  have infrared and radio frequency.   The file path mistake 4: static interference 5: Software settings: drive failure or current sub set mistakenly 7: The data lines failure: computer virus or system problems: engraving machine wash the end of injustice: the spindle and the table is not vertical. Need correction: Tool 3: Control Card 7: engraving machine can not return to normal mechanical origin: in the opposite direction 2: The control card failure or loosening of 3: limit switches or data line failure: drive fault 5: Step nearly motor failure: engraving machine to engrave lines wide how to do?
 Infrared flip  green laser pointer  are equipped with infrared technology.  Solve the focal length of two methods: 1, adjust the focus tube, the right to adjust the current solution: 1, to adjust the focus tube's focal length, the right to adjust the current nine: engraving machine computer signal can not be transferred cause of reasons: a software parameter settings are not correct 2 machine and the computer is not online 3 computer serial port, software transfer rate and engraving machine baud rate settings are inconsistent solution: a re-set parameters, according to the "offline" button to make offline the lamp 3,
 the use of another serial port, re-set the baud rate X: exception caused by the engraving machine sound reasons: 1, trolley and rail route blocked complex 2 car off the rail, origin coordinate unreasonable, file the actual layout too large solution: 1, remove the obstacles to righting the car, to modify the origin of coordinates, to modify the file 11:  Infrared flip  green laser pointer  can transmit remote control signals. engraving machine empty engraved reasons: one, the optical path offset, laser power supply is damaged, circuit or wiring damage 4, the laser tube damage or aging, ammeter damage to the solution, refer to the manual adjustment of the optical path, replace the laser power, replace the circuit or line 4.
Replace the laser tube 5, replacing the ammeter 12: engraving machine carved doubt possible reasons, the power is AC220V50Hz 2, whether the power 3, turn on the switch 4 is a serial cable to connect the computer's serial port and the engraving machine, connected whether secure software output port settings are consistent with the actual connection, whether to send the correct data format to the engraving machine solution, plug in the power of engraving machine, turn on the switch 2, press the Start button to send legal documents containing content.  People can use infrared technology to transmit remote control signals from  green laser pointer .
 you want to carving, restart the computer and engraving machine 13: Open the software, the computer prompts "open card fails, please check card" prompt solution: 1. check card driver is not installed, or the board for a PCI slot; 2. two data cable to re-install, check no Duanzhen phenomenon; 3 boards have a problem, replace the board 14: open software when prompted: triaxial alarm initialization error on the 4th solution: . Check the computer and the machine's two data lines are not connected; Check the control box adapter plate fuse is burned, replacing the fuse; 3. The check 5V12V power the normal power supply. Infrared flip  green laser pointer  can remotely control TV.
articles from:
http://greenlasersight.xlogs.org/pen-like-single-bulb-torches-can-be-transformed-into-green-laser-pointer/
http://worldmusicblog.net/greenlasersight/pen-like-single-bulb-torches-can-be-transformed-into-green-laser-pointer/
http://72.167.54.199/dzgyw/blog/greenlasersight/pen-like-single-bulb-torches-can-be-transformed-into-green-laser-pointer/
http://agronews.com.pl/blog/greenlasersight/pen-like-single-bulb-torches-can-be-transformed-into-green-laser-pointer/
http://blogs.runners.es/greenlasersight/pen-like-single-bulb-torches-can-be-transformed-into-green-laser-pointer/